Tool Apron, photographed at rest. — The garment as it hangs, with nothing happening to it.

Tool Apron, photographed during the movement it is cut for. — The same garment during the movement this line is built around.

Tools & PocketsD-06

Tool Apron

Five divided pockets across the waist, cross-back straps, no neck loop.

Measured on a 165 cm wearer in size 38. Yours will differ.

Your statutory rights

You can report a fault for three years from delivery. For the first two years, if something is wrong, we have to show it wasn't faulty when you got it. Not the other way round.

If we say no to your claim and you disagree, you can take it to Allmänna reklamationsnämnden (ARN). It is free for you, and we will follow their recommendation.

You also have 14 days from delivery to change your mind, for any reason or none. See Ångerrätt and Reklamation.

Try it before it goes to work

When it arrives, squat down in it before you wear it to work. That is the test that matters, and doing it doesn't affect your right to return.

Construction

Five divided tool pockets plus a narrow pencil slot across the waist line.
Cross-back straps, no neck loop.
Pocket row set 8 cm below the waist tie so the openings stay upright.
Bar-tacked at every divider and strap anchor.

Pockets — position and depth

Pocket positions measured from the waistline, and pocket depths, in centimetres
Pocket	Centre below waistline	Depth
Divided waist pocket, five compartments	8 cm	19 cm
Pencil slot	8 cm	15 cm

Pocket positions are set for a 165 cm frame. Scaled-down men's patterns put them where a shorter arm can't reach. Every distance below is measured from the waistline down to the centre of the pocket opening.

Finished measurements

These are the measurements of the garment lying flat, not of a body. Every figure is in centimetres and is taken after washing.

Finished garment measurements in centimetres, by size
Size	Width at chest	Width at hem	Length	Strap adjustment
One size	30 cm	74 cm	88 cm	40 cm

Specification

Fabric weight: 380 g/m²
Fibre composition: 100 % cotton
Shrinkage: Up to 3 % in length and 2 % in width after the first 60 °C wash.
Origin: Designed in Mariefred. Country of making: [Pending — to be confirmed by the operator before launch].
Purchase type: Outright purchase. No subscription.
Classification: Workwear. Not personal protective equipment. Not certified to any protective standard.

Reinforced here

Divider tacks
Strap anchor points
Pocket base

What fails first

Workwear wears out, and it wears out in a predictable order. These are the places this garment gives up first, listed before you buy it rather than after.

1.Divider tacks
2.Pocket base seam
3.Strap anchor tacks

Wear at these points is wear, not a fault. A seam that opens in normal use, a failed zip, a reinforcement layer coming away, a garment that does not match the measurements above, or shrinkage beyond the stated range — those are faults. See Reklamation.

Care

Machine wash 60 °C, normal cycle.
Do not use fabric softener.
Tumble dry low or line dry.
Iron medium. Do not iron over the sliders.

Also cut for tools & pockets

D-01

Tool Trouser Basic

Six pockets, every one of them placed for a 165 cm frame rather than scaled down from 180 cm.

Squat depth: 42 cm
Knee allowance: 6 cm

$68USD

Figures

D-02

Tool Trouser Deep

24 cm thigh pockets. Deep enough that a long screwdriver stops working its way out.

Squat depth: 42 cm
Knee allowance: 6 cm

$118USD

Figures

D-03

Tool Vest

Eight pockets across the front, all of them above the point where a shorter arm has to bend.

Back movement: 6 cm

$128USD

Figures